Use braces, tie-ins and guying as described by the scaffold's manufacturer at each end, vertically and horizontally to prevent tipping.Check for employees under the platform and provide falling object protection or barricade the area.Check for guardrails and midrails on platforms where work is being done.Check to see if the platform is 14 inches or more away from the wall or 18 inches or less away if plastering or stucco.Check to see if 10-foot or shorter planks are 6 to 12 inches over the center line of the support, and that 10-foot or longer planks are no more than 18 inches over the end.Check to see if the planks are close together, with spaces no more than 1 inch around uprights.If the planks deflect one-sixtieth (1/60) of the span or 2 inches in a 10-foot wooden plank, the plank has been damaged and must not be used.Check wooden planks for cracks, splits greater than one-quarter (1/4) inch, end splits that are long, many large loose knots, warps greater than one-quarter (1/4) inch, boards and ends with gouges, mold, separated laminate(s), and grain sloping greater than 1 in 12 inches from the long edge and are scaffold grade lumber or equivalent.Do not use the crossbraces as a ladder for access or exit. Check metal components for bends, cracks, holes, rust, welding splatter, pits, broken welds, and non-compatible parts.Check legs, posts, frames, and uprights to see if they are on baseplates and mudsills.Check footings to see if they are level, sound, rigid, and capable of supporting the loaded scaffold.Verify that the scaffold is the correct type for the loads, materials, employees, and weather conditions.Make sure that tools and materials are at least 10 feet away from energized powerlines.Check to see if powerlines near scaffolds are de-energized or that the scaffolds are at least 10 feet away from energized powerlines.Inspect scaffolds and scaffold parts daily, before each work shift, and after any event that may have caused damage. Before a scaffold is moved, each employee on the scaffold must be made aware of the move.Brief description of the inspection process that should be gone through before each work shift to ensure that there are no hazards related to the scaffold.No employee is on any part of the scaffold that extends beyond the wheels, casters, or other supports.Does not produce a speed in excess of 1 foot per second.When power systems are used, the propelling force is : Do not use the crossbraces as a ladder for access or exit.Outrigger frames, when used, are installed on both sides of the scaffold.The height to base width ratio of the scaffold during movement is 2:1 or less, unless the scaffold is designed and constructed to meet or exceed nationally recognized stability test requirements (such as ANSI/SIA A92.5 and 92.6).The surface on which the scaffold is being moved is :.Employees are not allowed to ride on scaffolds unless the following conditions exist :.Forklifts, trucks, motor vehicles, or add-on motors must not be used to propel scaffolds unless the scaffold is designed for them. Power systems used to propel mobile scaffolds must be designed for that purpose.Manual force used to move the scaffold must be applied as close to the base as practicable, but not more than 5 feet above the supporting surface.Scaffolds shall be stabilized to prevent tipping during movement.Scaffolds constructed of fabricated frame components must also comply with the requirements of paragraph (c) of this section.Scaffolds constructed of tube and coupler components must also comply with the requirements of paragraph (b) of this section. Leveling of the scaffold, where necessary, must be achieved by the use of :.Platforms must not extend beyond the base supports of the scaffold, unless stability is ensured by :.Caster stems and wheel stems in scaffold legs or adjustment screws must be :.To prevent movement of the scaffold while it is being used in a stationary position, scaffold casters and wheels must be locked with :.All brace connections must be secured.To prevent collapse of the scaffold, to secure vertical members together laterally and to automatically square and align vertical members, scaffolds must be braced by :.Scaffolds can often be a safer choice than ladders. They are designed to be easily moved and are commonly used for things like painting, plastering, drywall installation, or other jobs where workers must frequently change position. 1926.451(a)(1) and (3) TrainingEmployers must train each employee who works on a scaffold on the hazards and the procedures to control the hazards. Mobile scaffolds are a type of supported scaffold set on wheels or casters. Suspension scaffold rigging must at least 6 times the intended load. Scaffolds must be plumb, level, and squared. CapacityScaffolds and scaffold compponents must support at least 4 times the maximum intended load.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |